How to remove or delete linux from harddisk drive and restore the MBR partition table safely

Removing linux from windows partition - If you have a dual-boot with Linux and Windows, then you probably know that when you start your system Linux boot loader who first appeared to show Linux and then Windows boot entries and if you choose Windows from the list, it starts Windows.

Well now you are in situations when you want to remove Linux from your system and just want to use Windows, then how would you do?

A lot of people delete the Linux partition after installation of the "Disk Manager" can not delete it but Linux as a whole. Linux boot loader still appears at startup and as you remove the Linux partition, the boot loader will be corrupted and your system becomes unusable or being damaged

First of all you need to know where your Linux OS is installed to. that is what drive it is currently living on. Bear in mind that Linux formats the drive as HFS rather than Fat/Fat32 or NTFS. [These are the file systems used by various Operating Systems].

So HFS Partitions are not seen by windows, so its hidden.

To remove the partitions of Linux in WindowsXP go to your 'Control panel' - Admistrative Tools - Computer Managment

Open 'Disk Management' and you will see your Linux drives recognised as 'Unknown Partition' plus the status of the drive. Bearing in mind you know what partition and disk you installed to it will be easier to recognise as the drive/partition where you had installed it to.

Once you have identifed the drives, 'right-Click' on the drive/partiton and select 'Delete Logical Drive'

Once you have followed this through, you will now have free space.

This next part is very important. Once you have formatted the drive, re format it as your required file system type. either Fat32 or NTFS. Now the important part is coming up !

Fixing your Master Boot Record to make Windows Bootable again.

Have a Windows Boot disk with all the basic DOS Commands loaded on to the disk. A standard Windows 98/Me Boot Disk will work too.

Type in the DOS command :

e.g, from your C:\

fdisk /mbr

Or use your Windows XP run the recovery console, pick which xp install you would like to boot in to (usually you will pick #1)

then type: fixmbr , Answer Y to the dialogue.

Your master boot record will now be restored and Windows XP will be bootable once again. Your System will be restored with your original boot loader that you got with Windows XP.

Read More

Computer maintenance tips , take care before being damaged

How to care maintain a computer, pc, or laptop, especially the CPU will that usually only be done after get an error or being damaged. So, I think this is less precise. In their use of computers should be done periodically at both the CPU and the monitor. Actually there are some fundamental things that we often forget to do with how to care for a computer, which can cause damage to the computer.

Maybe, we may not realize it, but your computer and your car have something in common: they both need regular maintenance. No, you don't need to change your computer's oil. But you should be updating your software, keeping your antivirus subscription up to date, and checking for spyware. Read on to learn what you can do to help improve your computer's security.

Getting started

The following are some basics maintenance tasks you can do today to start improving your computer's security. Be sure you make these part of your ongoing maintenance as well.

* Sign up for software update e-mail notices. Many software companies will send you e-mail whenever a software update is available. This is particularly important for your operating system (e.g., Microsoft VV!|VD0VV$® or Macintosh), your antivirus program, and your firewall.
* Register your software. If you still have registration forms for existing software, send them in. And be sure to register new software in the future. This is another way for the software manufacturer to alert you when new updates are available.
* Install software updates immediately.
When you get an update notice, download the update immediately and install it. (Remember, downloading and installing are two separate tasks.)
An ounce of prevention

A few simple steps will help you keep your files safe and clean.

* Step 1: Update your software
* Step 2: Backup your files
* Step 3: Use antivirus software and keep it updated
* Step 4: Change your passwords


Developing ongoing maintenance practices

Now that you've done some ground work, it's time to start moving into longer term maintenance tasks. These are all tasks that you should do today (or as soon as possible) to get started. But for best results, make these a part of a regular maintenance schedule. We recommend setting aside time each week to help keep your computer secure.

* Back up your files. Backing up your files simply means creating a copy of your computer files that you can use in the event the originals are lost. (Accidents can happen.) To learn more read our tips for backing up information.

* Scan your files with up to date antivirus software. Use your antivirus scan tool regularly to search for potential computer viruses and worms. Also, check your antivirus program's user manual to see if you can schedule an automatic scan of your computer. To learn more, read our tips for reducing your virus risk

* Change your passwords. Using the same password increases the odds that someone else will discover it. Change all of your passwords regularly (we recommend monthly) to reduce your risk. Also, choose your passwords carefully. To learn more, read our tips for creating stronger passwords

Making a schedule

One of the best ways to help protect your computer is to perform maintenance regularly. To help you keep track, we suggest making a regular "appointment" with your computer. Treat it like you would any other appointment. Record it in your datebook or online calendar, and if you cannot make it, reschedule. Remember, you are not only helping to improve your computer, you are also helping to protect your personal information.

Read More

Digital Camera Tips and General Guide

Today, we increasingly realize that our needs will be documenting a moment it is very important. With digital cameras, we will be more easy to realize these purposes. However, before buying a digital camera here are a few tips,

Well, maybe buying one can be more than a little difficult. What types of features should you look for? Well, this guide will tell you that plus get you a little more familiar with what these cameras are capable of.

Megapixels
When it comes to megapixels, the more the better. I recommend a minimum of 2, but 3 or 4 is great. We did a test to see if a camera with 2.3 megapixels (actually 1.92 - 1600 x 1200) could produce a good quality 8x10.

Turns out it can, if you have the right paper and printer. We used HP Premium Plus photo paper with an HP 970 series printer and made a fantastic 8 x 10. Remember, I was a professional photographer before I got into computing, so I know a good print when I see it :-)

The resolution at 8x10 (we had to crop in to make the picture proportional to 8x10) was only 150 DPI. Most printers would not make a real good 8x10 at that resolution, but this one did. So, if you want to be sure you can get good 8 x 10s, you may want to go with a 3 megapixel camera or better (that gives you around 200 DPI at 8x10 size, still not quite the optimum 300 DPI, but it looks good with the right printer).

Optical vs Digital Zoom
You've probably noticed that most digital cameras have both a specification for digital and optical zoom. Pay the most attention to the optical zoom.

The optical zoom magnifies (zooms in) using glass. The digital zoom basically crops out the edge of the picture to make the subject appear closer, causing you to lose resolution or to get an interpolated resolution (i.e. the camera adds pixels). Neither of which help image quality.

Finally, make sure you get enough (optical) zoom. A 2x zoom isn't going to do much for you. A 3x is the average you'll find in most digital cameras will probably be good for most uses. More on lenses later.

Connection
How does the camera connect to your computer? If you have a USB port in your computer, you'll want a camera that can connect via USB as opposed to a slow serial connection.

On the other hand, if your computer doesn't have a USB port, is there a serial connector available for the camera you're looking at? If so, is it a special order and how long does it take to get it?

Storage
What does the camera use to store images with? If it uses a memory stick, make sure you consider buying additional sticks when you get your camera. A typical 8 meg memory stick that comes with a 2 megapixel camera only holds 5 or 6 images at the camera's best quality.

Some cameras use a 3.5 inch disk for storage. Be careful of these!
Although it may sound like a good idea, a 3 megapixel camera at high resolution produces a 1 meg file (compressed!). That's only 1 picture per disk.


Here's a few more things to look out for when trying to make your digital camera purchase.

Picture Formats
When you're trying to decide on which digital camera to get, check and see how many different picture formats it supports.

You want something that can produce both uncompressed (usually TIFF) and compressed (usually JPEG) images. I personally use the high quality JPEG setting on my camera for most of my shooting. TIFFs are just too big and the difference in quality is not ascertainable by mere mortals.

You also want to be able to shoot at a lower resolution than the camera's maximum. That way, If you're running short on memory, you can squeeze a few more shots on your memory stick.

Auxiliary Lens / Flash
This was a biggie for me. While a 3x zoom may work for the "average" user, I needed something that allowed me to do some wide angle work as well as have a good telephoto lens.

So, the camera I purchased a few months back was a Nikon Coolpix 990 (note that this isn't the only camera that can accept lenses). It has auxiliary lenses that screw into the filter ring on the front of the lens. I now have an ultra-wide fisheye lens plus a nice telephoto.

In addition to lenses, I wanted a good flash. The flash that is built into most of these cameras gives you a top range of 15-20 feet - at best. I wanted a camera that could take a powerful auxiliary flash (again, the Nikon isn't the only camera that fits this requirement, but I liked it better than the rest). If you need more reach than the small built in flash can deliver, then make sure you can attach an external flash to any camera you consider.

As an added bonus, if you get a camera that can take an external flash, you can place that flash on a bracket and eliminate red-eye.

Flash Distance
Speaking of flashes, make sure you check the distance the built in flash is good for. You don't want a camera with a wimpy flash that only travels a few feet (well, unless you can get an external flash for it as described above).

Battery Type
This may not sound important, but it is. Anyone who owns a digital camera can tell you they eat batteries the way a sumo wrestler eats at a buffet. Make sure the camera can run on regular (or rechargeable) "AA" type batteries. You don't want a camera that eats through expensive lithium batteries every 10 shots or so. One thing to remember about digital cameras, they do eat through batteries. I recommend getting some Nickel Metal Hydride rechargeable for it. I have some for mine and they have saved me a fortune.

Final Notes
Choosing a digital camera isn't easy. There's a huge selection out there and only you can determine which features you need.

For instance, if you shoot wildlife photos, a small 3x zoom probably isn't going to cut it (unless you can attach auxiliary lenses to it). If you shoot lots of close-ups, make sure the camera has some sort of macro capability. If you shoot big group photos indoors, an external flash may be necessary.

My advice is to make a list of things you want to be able to do with the camera then go to somewhere that can help you make a good purchase decision.

Finally, buy the BEST camera you can possibly afford. Or wait until the price drops on one with the type of features you want

Read More

Send error report in win xp - how to disable it?

Fo all of you xp users , to disable the stupid feature in WinXP which tries to send an error report to microsoft every time a program crashes you will have to do this:

Follow these steps:

- Open Control Panel
- Click on Preformance and Maintenance.
- Click on System.
- Then click on the Advanced tab
- Click on the error reporting button on the bottom of the windows.
- Select Disable error reporting.
- Click OK
- Click OK

OR

- Right-Click on My Computer icon
- Then click on the Advanced tab
- Click on the error reporting button on the bottom of the windows.
- Select Disable error reporting.
- Click OK
- Click OK

Related :

• XP Quick Fix Plus Download - Error Repair Tool
• Fix MSE, a utility to repair microsoft security essentials antivirus
• Host Process for Win32 Services Error , easy way to fix it

Read More

Tips to recover damaged or scratched disc (CD)

I've learned a primitive thecnique to how to recover damaged or scratched disks with some lost of data. In this case I have one borrowed a game - counter strike with a chunck of 7 mb lost with a scratch in CD1 Install. Here we cover some special thecniques of how to create a full working CD from the scratched one.

First some tools will be needed:

1. Alcohol 120%
2. UltraISO
3. Windows XP/2000 (not tested on 95/98/me)
3. Small piece of cotton
4. Dry cleaner paper
5. Finally, oil for cooking.

The steps ,

1- Preparing the CD

Get the cotton and drop some water, start cleaning vertically the surface of disc. Do it 3 times and dry the water with a piece of dry cleaner paper. With a new piece of cotton, drop some oil for cooking and start to wet the surface like you are washing the CD with the oil. Dry carefully now. Some particles of oil will stay on the microsurface of the scrath. It's okay. Seems the oil helps the laser of the CD/DVD driver to read the surface again. Sure this will work with small unreadable scratchs - some hard scratchs loose parts of the surface of the CD where we have data and it's lost forever. But if it is loosed try anyway. Whith this tip 80% of the small scratched CD's coud be recovered.

2 - Testing the CD

With Alcohol 120% make an ISO - image making wizard - and lets see if the app can
read the loosed surface. In my case Alcohol 120% had recovered 60% of the data.
This is not enough. Have tryed other appz, they do not recover all the data. But the
CD/DVD driver laser CAN recover all data in this case. the data is still there, what we do?

3 - Making the new CD

With the main copy system of windows explorer you can do it. Just create one folder with the same name of the CD label for future burn reference, and copy the CD content to the folder. When the CD copy process find the scratch, in majority of the cases, it's slow down the reading and will recover ALL loosed data. If not, it just tell you there's an unreadable sector.
In this case your CD is lost. But it's not my case, finally windows explorer got all the data from the scratch and made a copy in the folder. With the ultraISO, wrote the original CD label, drop the content of the folder and save as Iso. You can Test the new CD just mounting the iso in the Alcohol 120%. Here, in my case i did ISO of the two discs from counter strike and tested installing from the mounted ISO. Works like a charm. I got the 7 mb lost again. So, I have burned the CD and now I have a working copy from the scratched one.

Sounds too bizzarre, but works. Course you can jump the cleaning process and try to copy the content with Windows explorer. But in my case did not work without oil...

Read More

Edit, Remove, and Add Right-Click Menu Items from Files and Folders

As we know,some programs ask you if you want to option and others do not. Now granted, I probably said yes a couple of times, thinking how useful it would be to have that in my right-click menu, but there are still some I don’t even use.

There are many windows aplications that you install will add themselves to the right-click menu of your files and/or folders. And most times, you have no choice in the matter and, as a result, your right-click menu can get very long with added items you don't even use. The last person I was helping with this had a right context menu so long that the Rename option was no longer visible!

Fortunately, we can easily remove those unwanted menu items, if you know the registry values to edit. And it's not at all difficult once you know the keys responsible for the additions.

For Files, the secret lies in the "context menu handlers" under the shellex subkey for "All Files" which, in the registry, is nothing but an asterisk - like a dos wildcard, which means the values entered apply to all files. It is at the very top of the Root key, right here (go to:Start - Run - type : regedit) :

HKEY_CLASSES_ROOT\*\shellex\ContextMenuHandlers

Click the the + sign next to the ContextMenuHandlers key, to expand it.
Now you will see some of the programs that have added items to your right-click menu. Simply delete the program keys you don't want.
Yes, really simple, right. If deleting makes you uneasy, just export the key before deleting it. Or, instead of deleting the values, disable them. Simply double click the default value for the program on the right hand pane and rename the clsid value by placing a period or dash in front of it.

ie; - {b5eedee0-c06e-11cf-8c56-444553540000}

Then exit the registry, refresh, and right click a file to see if the item was removed from the menu.

Some programs - like WinZip or WinRar - will add several items to your right click menu but all of them will be removed by deleting or disabling their one context menu handler.

Note that the above key only applies to the right click menu of files.
To remove entries from the right click context menu of folders, you need to navigate to the Folder and Drive keys:

HKEY_CLASSES_ROOT\Folder\shellex\ContextMenuHandlers
HKEY_CLASSES_ROOT\Drive\shellex\ContextMenuHandlers

All you have to do is follow the same procedure as for Files - either disable or delete items you wish to remove.
Adding Items
Adding Items to the right click menu of Files and Folders is also fairly simple using the Registry. It just involves the creation of a few new keys for each item you wish to add. You edit the same keys used for removing items. Let's use Notepad as an example of an item you'd like to add to the right click menu of all your files or folders.

For folders, go to this key:
HKEY_CLASSES_ROOT\Folder
Click the + sign next to Folder and expand it so that the Shell key is visible. Right click the Shell key and choose New>Key and name the key Notepad or whatever else you'd prefer (whatever the key is named is what will appear in the right-click menu). Now right click the new key you made and create another key named Command. Then, in the right hand pane, double click "Default" and enter Notepad.exe as the value.
Exit the registry, refresh, and right click any folder. Notepad should now be on the context menu.

For files, go here again:

HKEY_CLASSES_ROOT\*
Expand the * key and see if a Shell key exists. If it does exist, follow the same procedure as for folders. If it does not exist, you'll have to create a new Shell first. Just right click the * key and choose New>Key and name it Shell. Then right click the Shell key and continue on the same way you did for adding items to the right click menu of folders.

Once done, Notepad should appear as an option in the right click menu of all your files.

Read More